View MB89185L_1853486.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ds07-12557-1e fujitsu semiconductor data sheet 8-bit proprietary microcontroller cmos f 2 mc-8l mb89180l series mb89183l/185l/p185/pv180 n description the mb89180l series is a line of the general-purpose, single-chip microcontrollers. in addition to a compact instruction set, the microcontrollers contain a variety of peripheral functions such as an lcd controller/driver, timers, a serial interface, and external interrupts. n features ?f 2 mc-8l family cpu core ? dual-clock control system ? maximum memory size: 16-kbyte rom, 512-byte ram (max) ? minimum execution time: 0.95 m s/4.2 mhz ? i/o ports: max 43 channels ? 21-bit time-base timer ? 8/16-bit timer/counter: 2 or 1 channels ? 8-bit serial i/o: 1 channel ? external interrupts (wake-up function): four channels with edge detection plus eight level-interrupt channels ? watch prescaler (15 bits) ? lcd controller/driver: 32 segments 4 commons (max 128 pixels) ? lcd driving reference voltage generator ? remote control transmission output ? buzzer output ? power-on reset function (option) ? low-power consumption modes (stop, sleep, and watch mode) ? cmos technology
mb89180l series 2 n packages 64-pin plastic sqfp 64-pin plastic qfp 64-pin plastic qfp (fpt-64p-m03) (fpt-64p-m06) (fpt-64p-m09) 64-pin ceramic mqfp (mqp-64c-p01)
mb89180l series 3 n product lineup (continued) part number parameter mb89183l MB89185L mb89p185 mb89pv180 classification mass production products (mask rom products) one-time prom product piggyback/evaluation product (for development) rom size 8 k 8 bits (internal mask rom) 16 k 8 bits (internal mask rom) 16 k 8 bits (internal prom, programming with general-purpose eprom programmer) 32 k 8 bits (external rom) ram size 256 8 bits 512 8 bits cpu functions number of instructions : 136 instruction bit length : 8 bits instruction length : 1 byte to 3 bytes data bit length : 1, 8,16 bits minimum execution time : 0.95 m s/4.2 mhz interrupt processing time : 8.6 m s to 137.1 m s /4.2 mhz ports i/o port (n-ch open-drain) : 8 (6 ports also serve as peripherals, 3 ports are a heavy-current drive type.) output ports (n-ch open-drain) : 18 (16 ports also serve as segment pins *2 , 2 ports also serve as common pins.) i/o ports (cmos) : 16 (12 ports also serve as an external interrupt, 8 ports also serve as segment pins.) output ports (cmos) : 1 (also serve as peripherals) total : 43 (max) timer/counter 8-bit timer operation (toggled output capable, operating clock cycle 1.9 m s to 487.6 m s) 16-bit timer operation (toggled output capable, operating clock cycle 1.9 m s to 487.6 m s) serial i/o 8 bits lsb first/msb first selectability one clock selectable from four operation clocks (one external shift clock, three internal shift clocks: 1.9 m s, 7.6 m s, 30.5 m s) lcd controller/ driver common output : 4 (max) segment output : 32 (max) *2 bias power supply pins : 3 lcd display ram size : 32 4 bits dividing resistor for lcd driving:built-in (an external resistor selectability)
mb89180l series 4 (continued) *1 : varies with conditions such as the operating frequency. *2 : see n mask options. n package and corresponding products : available : not available note: for more information about each package, see n package dimensions. part number parameter mb89183l MB89185L mb89p185 mb89pv180 external interrupt 1 (wake-up function) 4 independent channels (edge selectability) rising edge/falling edge selectability used also for wake-up from stop/sleep mode. (edge detection is also permitted in stop mode.) external interrupt 2 (wake-up function) l level interrupts 8 channels buzzer output 1 (7 frequencies are selectable by the software.) remote control transmission output 1 (pulse width and cycle are software selectable.) standby modes subclock mode, sleep mode, stop mode, and watch mode process cmos operating voltage 2.2 v to 3.6 v *1 2.7 v to 6.0 v eprom for use mbm27c256a-20tv package mb89183l MB89185L mb89p185 mb89pv180 fpt-64p-m03 fpt-64p-m06 fpt-64p-m09 mqp-64c-p01
mb89180l series 5 n differences among products 1. memory size before evaluating using the piggyback product, verify its differences from the product that will actually be used. take particular care on the following points: ? on the mb89183l, MB89185L and mb89p185, addresses 0180 h and later of the register bank cannot be used. ? the stack area, etc., is set at the upper limit of the ram. 2. current consumption ? in the case of the mb89pv180, add the current consumed by the eprom which is connected to the top socket. ? when operated at low speed, the product with an otprom (one-time prom) or an eprom will consume more current than the product with a mask rom. however, the current consumption in the sleep/stop modes is the same. (for more information, see n electrical characteristics.) 3. mask options functions that can be selected as options and how to designate these options vary by the product. before using options check n mask options. take particular care on the following points: ? a pull-up resistor cannot be set for p20 to p27, p40 to p47 and p50 to p57 on the mb89p185. ? a pull-up resistor is not selectable for p10 to p17, p40 to p47 and p50 to p57 if they are used as lcd pins. ? options are fixed on the mb89pv180.
mb89180l series 6 n pin assignments (continued) seg4 seg5 seg6 seg7 p40/seg8* 1 p41/seg9* 1 p42/seg10* 1 p43/seg11* 1 p44/seg12* 1 p45/seg13* 1 p46/seg14* 1 p47/seg15* 1 p50/seg16* 1 p51/seg17* 1 p52/seg18* 1 p53/seg19* 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 p54/seg20* 1 p55/seg21* 1 p56/seg22* 1 p57/seg23* 1 p10/seg24/int10* 1 p11/seg25/int11* 1 p12/seg26/int12* 1 v ss p13/seg27/int13* 1 p14/seg28* 1 p15/seg29* 1 p16/seg30* 1 p17/seg31* 1 p27/buz* 2 p26* 2 p25/sck 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 p03/int23 p04/int24 p05/int25 p06/int26 p07/int27 rst x0a x1a moda x0 x1 p20/ec p21* 2 p22/to p23/si p24/so 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 seg3 seg2 seg1 seg0 com0 com1 p31/com2 p32/com3 v cc v3 v2 v1 p30/rco p00/int20 p01/int21 p02/int22 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 (top view) *1 : selected using the mask option (in units of 4 pins). *2 : n-ch open drain heavy-current drive type for more information on mask option combinations of *1, see n mask options. (fpt-64p-m03)
mb89180l series 7 (continued) seg4 seg5 seg6 seg7 p40/seg8* 1 p41/seg9* 1 p42/seg10* 1 p43/seg11* 1 p44/seg12* 1 p45/seg13* 1 p46/seg14* 1 p47/seg15* 1 p50/seg16* 1 p51/seg17* 1 p52/seg18* 1 p53/seg19* 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 p54/seg20* 1 p55/seg21* 1 p56/seg22* 1 p57/seg23* 1 p10/seg24/int10* 1 p11/seg25/int11* 1 p12/seg26/int12* 1 v ss p13/seg27/int13* 1 p14/seg28* 1 p15/seg29* 1 p16/seg30* 1 p17/seg31* 1 p27/buz* 2 p26* 2 p25/sck 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 p03/int23 p04/int24 p05/int25 p06/int26 p07/int27 rst x0a x1a moda x0 x1 p20/ec p21* 2 p22/to p23/si p24/so 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 seg3 seg2 seg1 seg0 com0 com1 p31/com2 p32/com3 v cc v3 v2 v1 p30/rco p00/int20 p01/int21 p02/int22 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 (top view) *1: selected using the mask option (in units of 4 pins). *2: n-ch open drain heavy-current drive type for more information on mask option combinations of *1, see n mask options. (fpt-64p-m09)
mb89180l series 8 (continued) *1: selected using the mask option (in units of 4 pins). *2: n-ch open drain heavy-current drive type for more information on mask option combinations of *1, see n mask options. (top view) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 p01/int21 p02/int22 p03/int23 p04/int24 p05/int25 p06/int26 p07/int27 rst x0a x1a moda x0 x1 p20/ec p21* 2 p22/to p23/si p24/so p25/sck 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 seg2 seg1 seg0 com0 com1 p31/com2 p32/com3 v cc v3 v2 v1 p30/rco p00/int20 64 63 62 61 60 59 58 57 56 55 54 53 52 p56/seg22* 1 p57/seg23* 1 p10/seg24/int10* 1 p11/seg25/int11* 1 p12/seg26/int12* 1 v ss p13/seg27/int13* 1 p14/seg28* 1 p15/seg29* 1 p16/seg30* 1 p17/seg31* 1 p27/buz* 2 p26* 2 20 21 22 23 24 25 26 27 28 29 30 31 32 seg3 seg4 seg5 seg6 seg7 p40/seg8* 1 p41/seg9* 1 p42/seg10* 1 p43/seg11* 1 p44/seg12* 1 p45/seg13* 1 p46/seg14* 1 p47/seg15* 1 p50/seg16* 1 p51/seg17* 1 p52/seg18* 1 p53/seg19* 1 p54/seg20* 1 p55/seg21* 1 (fpt-64p-m06)
mb89180l series 9 (continued) (top view) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 p01/int21 p02/int22 p03/int23 p04/int24 p05/int25 p06/int26 p07/int27 rst x0a x1a moda x0 x1 p20/ec p21* 2 p22/to p23/si p24/so p25/sck 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 seg2 seg1 seg0 com0 com1 p31/com2 p32/com3 v cc v3 v2 v1 p30/rco p00/int20 64 63 62 61 60 59 58 57 56 55 54 53 52 p56/seg22* 1 p57/seg23* 1 p10/seg24/int10* 1 p11/seg25/int11* 1 p12/seg26/int12* 1 v ss p13/seg27/int13* 1 p14/seg28* 1 p15/seg29* 1 p16/seg30* 1 p17/seg31* 1 p27/buz* 2 p26* 2 20 21 22 23 24 25 26 27 28 29 30 31 32 seg3 seg4 seg5 seg6 seg7 p40/seg8* 1 p41/seg9* 1 p42/seg10* 1 p43/seg11* 1 p44/seg12* 1 p45/seg13* 1 p46/seg14* 1 p47/seg15* 1 p50/seg16* 1 p51/seg17* 1 p52/seg18* 1 p53/seg19* 1 p54/seg20* 1 p55/seg21* 1 (mqp-64c-m01) *1: selected using the mask option (in units of 4 pins). *2: n-ch open drain heavy-current drive type pin assignment on package top (mb89pv180 only) n.c.: internally connected. do not use. for more information on mask option combinations of *1, see n mask options. pin no. pin pin no. pin pin no. pin pin no. pin 65 n.c. 73 a2 81 n.c. 89 oe 66 v pp 74 a1 82 o4 90 n.c. 67a1275a083o591a11 68 a7 76 n.c. 84 o6 92 a9 69 a6 77 o1 85 o7 93 a8 70 a5 78 o2 86 o8 94 a13 71 a4 79 o3 87 ce 95 a14 72 a3 80 v ss 88 a10 96 v cc
mb89180l series 10 n pin description (continued) pin no. pin name i/o circuit type function sqfp* 1 qfp* 2 mqfp* 3 qfp* 4 39 40 x0 a crystal or other resonator connector pins for the main clock. the external clock can be connected to x0. when this is done, be sure to leave x1 open. 38 39 x1 40 41 moda c memory access mode setting pin. connect directly to v ss . 43 44 rst d reset i/o pin. this pin is an n-ch open-drain output type with a pull-up resistor, and a hysteresis input type. l is output from this pin by an internal reset request (optional). the internal circuit is initialized by the input of l. 44 to 51 45 to 52 p07/int27 to p00/int20 e general-purpose i/o ports. also serve as an external interrupt 2 input (wake-up function). external interrupt 2 input is hysteresis input. 21 to 23 22 to 24 p10/seg24/ int10 to p12/seg26/ int12 e/k general-purpose i/o ports. also serve as input for external interrupt 1 input. the interrupt 1 input is a hysteresis type. also serve as lcd controller/driver segment output. switching is done by the mask option. 25 26 p13/seg27/ int13 26 to 29 27 to 30 p14/seg28 to p17/seg31 f/k general-purpose i/o ports. also serve as lcd controller/driver segment output. switching is done by the mask option. 37 38 p20/ec h general-purpose n-ch open-drain i/o port. also serves as the external clock input for the 8-bit timer counter. the resource is a hysteresis input type. 36 37 p21 i general-purpose n-ch open-drain i/o port. 35 36 p22/to i general-purpose n-ch open-drain i/o port. also servers as the 8-bit timer/counter output. 34 35 p23/si h n-ch open-drain general-purpose i/o port. also serves as the data input for the serial i/o. the peripheral is a hysteresis input type. 33 34 p24/so i n-ch open-drain general-purpose i/o port. also serves as the data output for the 8-bit serial i/o. 32 33 p25/sck h n-ch open-drain general-purpose i/o port. also serves as the clock i/o for the 8-bit serial i/o. the peripheral is a hysteresis input type. 31 32 p26 i n-ch open-drain general-purpose i/o port.
mb89180l series 11 (continued) *1 : fpt-64p-m03 *2 : fpt-64p-m09 *3 : mqp-64c-p01 *4 : fpt-64p-m06 pin no. pin name i/o circuit type function sqfp *1 qfp *2 mqfp *3 qfp *4 30 31 p27/buz i n-ch open-drain general-purpose i/o port. also serves as buzzer output. 52 53 p30/rco g general-purpose output-only port. also serves as a remote control transmit output. 13 to 20 14 to 21 p50/seg16 to p57/seg23 j/k n-ch open-drain general-purpose output ports. also serve as an lcd controller/driver segment output. switching between port and segment output is done by the mask option. 5 to 12 6 to 13 p40/seg8 to p47/seg15 j/k 61 to 64 1 to 4 62 to 64 1 to 5 seg7 to seg0 k lcd controller/driver segment output-only pins. 57, 58 58, 59 p32/com3, p31/com2 l n-ch open-drain general-purpose output ports. also serve as an lcd controller/driver common output pins. 59, 60 60, 61 com1, com0 k lcd controller/driver common output-only pins. 53, 54, 55 54, 55, 56 v1, v2, v3 ? lcd driving power supply pins. 42 43 x0a b subclock crystal oscillator pins (32.768 khz) 41 42 x1a 56 57 vcc ? power supply pin. 24 25 vss ? power supply (gnd) pin.
mb89180l series 12 ? external eprom pins (mb89pv180 only) pin no. pin name i/o function 66 v pp o h level output pin 67 68 69 70 71 72 73 74 75 a12 a7 a6 a5 a4 a3 a2 a1 a0 o address output pins 77 78 79 o1 o2 o3 i data input pins 80 vss o power supply (gnd) pin 82 83 84 85 86 o4 o5 o6 o7 o8 i data input pins 87 ce o rom chip enable pin outputs h during standby. 88 a10 o address output pin 89 oe o rom output enable pin outputs l at all times. 91 92 93 a11 a9 a8 o address output pins 94 a13 o 95 a14 o 96 vcc o eprom power supply pin 65 76 81 90 n.c. internally connected pins be sure to leave them open.
mb89180l series 13 n i/o circuit type (continued) type circuit remarks a main clock (main clock crystal oscillator) ? at an oscillation feedback resistor of approximately 1 m w ? cr oscillation is selectable. (mb8918x only) b subclock (subclock crystal oscillator) ? at an oscillation feedback resistor of approximately 4.5 m w c ? hysteresis input ? the pull-down resistor (r) is approximately 50 k w for mb89183l/185l only. d ? at an output pull-up resistor (p-ch) of approximately 50 k w ? hysteresis input e ? cmos output ? cmos input ? the peripheral is a hysteresis input type. ? pull-up resistor optional (except mb89pv180) approximately 50 k w f ? cmos output ? cmos input ? pull-up resistor optional (except mb89pv180) approximately 50 k w x1 x0 n-ch p-ch p-ch n-ch x1a x0a n-ch p-ch p-ch n-ch n-ch r p-ch n-ch r p-ch n-ch r p-ch port peripheral p-ch n-ch r p-ch port
mb89180l series 14 (continued) type circuit remarks g ? cmos output ? p-ch output is a heavy-current drive type. h ? n-ch open-drain output ? cmos input ? the peripheral is a hysteresis input type. ? pull-up resistor optional (except mb89p185, and mb89pv180) approximately 50 k w i ? n-ch open-drain output ? cmos input ? p21, p26, and p27 are a heavy-current drive type. ? pull-up resistor optional (except mb89p185 and mb89pv180) approximately 50 k w j ? n-ch open-drain output ? pull-up resistor optional (except mb89p185 and mb89pv180) approximately 50 k w k ? lcd controller/driver common/segment output l ? n-ch open-drain output ? common output p-ch n-ch n-ch r p-ch port peripheral n-ch r p-ch port n-ch r p-ch n-ch p-ch p-ch n-ch n-ch p-ch p-ch n-ch n-ch
mb89180l series 15 n handling devices 1. preventing latchup latchup may occur on cmos ics if voltage higher than v cc or lower than v ss is applied to input and output pins other than medium- to high-voltage pins or if higher than the voltage which shows on 1. absolute maximum ratings in n electrical characteristics is applied between v cc to v ss . when latchup occurs, power supply current increases rapidly and might thermally damage elements. when using, take great care not to exceed the absolute maximum ratings. 2. treatment of unused input pins leaving unused input pins open could cause malfunctions. they should be connected to a pull-up or pull-down resistor. 3. treatment of n.c. pin be sure to leave (internally connected) n.c. pins open. 4. power supply voltage fluctuations although v cc power supply voltage is assured to operate within the rated range, a rapid fluctuation of the voltage could cause malfunctions, even if it occurs within the rated range. stabilizing voltage supplied to the ic is therefore important. as stabilization guidelines, it is recommended to control power so that v cc ripple fluctuations (p-p value) will be less than 10% of the standard v cc value at the commercial frequency (50 hz to 60 hz) and the transient fluctuation rate will be less than 0.1 v/ms at the time of a momentary fluctuation such as when power is switched. 5. precautions when using an external clock even when an external clock is used, oscillation stabilization time is required for power-on reset (optional) and wake-up from stop mode. 6. note to noise in the external reset pin (rst ) if the reset pulse applied to the external reset pin (rst ) does not meet the specifications, it may cause malfunc- tions. use caution so that the reset pulse less than the specifications will not be fed to the external reset pin (rst ) .
mb89180l series 16 n programming to the eprom on the mb89p185 the mb89p185 is an otprom version of the mb89180l series. 1. features ? 16-kbyte prom on chip ? options can be set using the eprom programmer. ? equivalency to the mbm27c256a in eprom mode (when programmed with the eprom programmer) 2. memory space memory space in each mode such as 16-kbyte prom, option area is diagrammed below. 3. programming to the eprom in eprom mode, the mb89p185 functions equivalent to the mbm27c256a. this allows the prom to be programmed with a general-purpose eprom programmer (the electronic signature mode cannot be used) by using the dedicated socket adapter. when the operating area for a single chip is 16 kbyte (c000 h to ffff h ) the prom can be programmed as follows: ? programming procedure (1) set the eprom programmer to the mbm27c256a. (2) load program into the eprom programmer at 4000 h to 7fff h . (note that addresses c000 h to ffff h while operating as a single chip assign to 4000 h to 7fff h in eprom mode.) load option data into address 3ff0 h to 3ff5 h of the eprom programmer. (for information about each corresponding option, see 7. setting otprom options.) (3) program with the eprom programmer. 0000 h ffff h i/o ram not available prom 16 kb 3ff6 h 7fff h not available eprom 16 kb single-chip eprom mode (corresponding addresses on the eprom programmer) 0080 h 0180 h not available not available 3ff0 h c000 h 4000 h option area 0000 h 8000 h address
mb89180l series 17 4. recommended screening conditions high-temperature aging is recommended as the pre-assembly screening procedure for a product with a blanked otprom microcomputer program. 5. programming yield all bits cannot be programmed at fujitsu shipping test to a blanked otprom microcomputer, due to its nature. for this reason, a programming yield of 100% cannot be assured at all times. 6. eprom programmer adapter socket package compatible adapter socket fpt-64p-m09 rom-64qf2-28dp-8l2 fpt-64p-m06 rom-64qf-28dp-8l3 program, verify aging +150 ?c, 48 h data verification assembly
mb89180l series 18 7. setting otprom options the programming procedure is the same as that for the prom. options can be set by programming value at the addresses shown on the memory map. the relationship between bits and options is shown on the following bit map: otprom option bit map notes : set each bit to 1 to erase. do not write 0 to the vacant bit. the read value of the vacant bit is 1, unless 0 is written to it. address 3ff6 h cannot be read and should not be accessed. bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 3ff0 h vacancy readable vacancy readable oscillation stabilization time vacancy readable reset pin output 1: yes 0: no clock mode selection 1: dual clock 0: single clock power-on reset 1: yes 0: no wtm1 wtm0 see n mask options. 3ff1 h p07 pull-up 1: no 0: yes p06 pull-up 1: no 0: yes p05 pull-up 1: no 0: yes p04 pull-up 1: no 0: yes p03 pull-up 1: no 0: yes p02 pull-up 1: no 0: yes p01 pull-up 1: no 0: yes p00 pull-up 1: no 0: yes 3ff2 h p17 pull-up 1: no 0: yes p16 pull-up 1: no 0: yes p15 pull-up 1: no 0: yes p14 pull-up 1: no 0: yes p13 pull-up 1: no 0: yes p12 pull-up 1: no 0: yes p11 pull-up 1: no 0: yes p10 pull-up 1: no 0: yes 3ff3 h vacancy readable vacancy readable vacancy readable vacancy readable vacancy readable vacancy readable vacancy readable vacancy readable 3ff4 h vacancy readable vacancy readable vacancy readable vacancy readable vacancy readable vacancy readable vacancy readable vacancy readable 3ff5 h vacancy readable vacancy readable vacancy readable vacancy readable vacancy readable vacancy readable vacancy readable vacancy readable
mb89180l series 19 n programming to the eprom with piggyback/evaluation device 1. eprom for use mbm27c256a-20tv 2. programming socket adapter to program to the prom using an eprom programmer, use the socket adapter (manufacturer: sun hayato co., ltd.) listed below. inquiry: sunhayato corp. : tel : 81-3-3984-7791 fax : 81-3-3971-0535 e-mail : adapter@sunhayato.co.jp 3. memory space memory space in each mode, such as 16-kbyte prom, option area is diagrammed below. 4. programming to the eprom (1) set the eprom programmer to the mbm27c256a. (2) load program data into the eprom programmer at 4000 h to 7fff h . (3) program to 4000 h to 7fff h with the eprom programmer. package adapter socket part number lcc-32 (rectangle) rom-32lc-28dp-yg lcc-32 (square) rom-32lc-28dp-s i/o ram not available prom (16kb) eprom (16kb) 0000 h 0080 h 8000 h ffff h 7fff h 0000 h normal operation mode (corresponding addresses on the eprom programmer) 0280 h c000 h 4000 h not available not available
mb89180l series 20 n block diagram oscillator clock controller low-power oscillator (32.768 khz) ram f 2 mc-8l cpu rom other pins moda internal data bus 21-bit timebase 8-bit 8-bit serial i/o port 2 n-ch open-drain i/o port port 1 *1: the segment or port function is selected by the mask option. *2: n-ch open-drain heavy-current drive type. x0 x1 p00/int20 to p07/int27 p22/to p20/ec p25/sck p24/so p23/si p14 to p17 timer (max 4.2 mhz) main clock x0a x1a external interrupt 2 (wake-up function) port 0 cmos i/o port port 3 n-ch open-drain output port (only p30 for cmos output port) 8 8 timer/counter 1 (timer 1) 8-bit timer/counter 2 (timer 2) 4 cmos i/o port lcd controller/driver 32 4-bit display ram (16 bytes) buzzer output port 4 and port 5 n-ch open-drain output port p10/int10 to p13/int13 4 seg24 *1 to seg27 *1 (also serve as p10 to p13) 4 seg0 to seg7 8 com0 to com1 2 v1 to v3 3 8 subclock remote control transmission output p30/rco p31/com2 p32/com3 reset circuit (watchdog timer) rst vcc vss moda vcc vss p26 *2 p21 *2 p27 *2 /buz external interrupt 1 (wake-up function) 4 4 p31/com2 p32/com3 16 p57/seg23 *1 to p54/seg20 *1 4 p43/seg11 *1 to p40/seg8 *1 4 p53/seg19 *1 to p50/seg16 *1 4 p47/seg15 *1 to p44/seg12 *1 4 seg28 *1 to seg31 *1 (also serve as p14 to p17)
mb89180l series 21 n cpu core 1. memory space the microcontrollers of the mb89180l series offer a memory space of 64 kbytes for storing all of i/o, data, and program areas. the i/o area is located at the lowest address. the data area is provided immediately above the i/o area. the data area can be divided into register, stack, and direct areas according to the application. the program area is located at exactly the opposite end, that is, near the highest address. provide the tables of interrupt reset vectors and vector call instructions toward the highest address within the program area. the memory space of the mb89180l series is structured as illustrated below. memory space vector table (reset, interrupt, vector call instruction) i/o ram rom mb89183l 0000 h 0080 h 0100 h 0180 h ffc0 h ffff h e000 h access prohibited registers i/o ram rom mb89pv180 0000 h 0080 h 0100 h 0200 h 0280 h ffc0 h ffff h 8000 h access prohibited registers i/o ram rom MB89185L mb89p185 0000 h 0080 h 0100 h 0180 h ffc0 h ffff h c000 h access prohibited registers external
mb89180l series 22 2. registers the f 2 mc-8l family has two types of registers; dedicated registers in the cpu and general-purpose registers in the memory. the following dedicated registers are provided: program counter (pc) : a 16-bit register for indicating instruction storage positions accumulator (a) : a 16-bit temporary register for storing arithmetic operations, etc. when the instruction is an 8-bit data processing instruction, the lower byte is used. temporary accumulator (t) : a 16-bit register which performs arithmetic operations with the accumulator. when the instruction is an 18-bit data processing instruction, the lower byte is used. index register (ix) : a 16-bit register for index modification extra pointer (ep) : a 16-bit pointer for indicating a memory address stack pointer (sp) : a 16-bit register for indicating a stack area program status (ps) : a 16-bit register for storing a register pointer, a condition code the ps can further be divided into higher 8 bits for use as a register bank pointer (rp) and the lower 8 bits for use as a condition code register (ccr). (see the diagram below.) pc a t ix ep sp ps 16 bits : program counter : accumulator : temporary accumulator : index register : extra pointer : stack pointer : program status fffd h undefined undefined undefined undefined undefined i-flag = 0, il1, 0 = 11 other bits are undefined. initial value structure of the program status register vacancy h i il1, 0 n z vc 54 rp ps 109876 3210 15 14 13 12 11 rp ccr vacancy vacancy
mb89180l series 23 the rp indicates the address of the register bank currently in use. the relationship between the pointer contents and the actual address is based on the conversion rule illustrated below. the ccr consists of bits indicating the results of arithmetic operations and the contents of transfer data and bits for control of cpu operations at the time of an interrupt. h-flag : set when a carry or a borrow from bit 3 to bit 4 occurs as a result of an arithmetic operation. cleared otherwise. this flag is for decimal adjustment instructions. i-flag : interrupt is allowed when this flag is set to 1. interrupt is prohibited when the flag is set to 0. set to 0 when reset. il1, 0 : indicates the level of the interrupt currently allowed. processes an interrupt only if its request level is higher than the value indicated by this bit. n-flag : set if the msb is set to 1 as the result of an arithmetic operation. cleared when the bit is set to 0. z-flag : set when an arithmetic operation results in 0. cleared otherwise. v-flag : set if the complement on 2 overflows as a result of an arithmetic operation. reset if the overflow does not occur. c-flag : set when a carry or a borrow from bit 7 occurs as a result of an arithmetic operation. cleared otherwise. set the shift-out value in the case of a shift instruction. il1 il0 interrupt level high-low 00 1 high low = no interrupt 01 10 2 11 3 rule for conversion of actual addresses of the general-purpose register area ? a15 ? a14 ? a13 ? a12 ? a11 ? a10 ? a9 ? a8 r4 a7 r3 a6 r2 a5 r1 a4 r0 a3 b2 a2 b1 a1 b0 a0 lower op codes rp generated addresses
mb89180l series 24 the following general-purpose registers are provided: general-purpose registers: an 8-bit register for storing data the general-purpose registers are 8 bits and located in the register banks of the memory. one bank contains eight registers. up to a total of 16 banks can be used on the mb89183l, MB89185L and mb89p185 (ram 256 8 bits), and a total of 32 banks can be used on the mb89pv180 (ram 512 8 bits). the bank currently in use is indicated by the register bank pointer (rp). note : the number of register banks that can be used varies with the ram size. register bank configuration this address = 0100 h + 8 (rp) memory area 16 banks (mb89183l) 32 banks (MB89185L) r 0 r 1 r 2 r 3 r 4 r 5 r 6 r 7
mb89180l series 25 n i/o map (continued) address read/write register name register description 00 h (r/w) pdr0 port 0 data register 01 h (w) ddr0 port 0 data direction register 02 h (r/w) pdr1 port 1 data register 03 h (w) ddr1 port 1 data direction register 04 h (r/w) pdr2 port 2 data register 05 h (w) ddr2 port 2 data direction register 06 h vacancy 07 h (r/w) sycc system clock control register 08 h (r/w) stbc standby control register 09 h (r/w) wdtc watchdog timer control register 0a h (r/w) tbtc time-base timer control register 0b h (r/w) wpcr watch prescaler control register 0c h (r/w) pdr3 port 3 data register 0d h vacancy 0e h (r/w) pdr4 port 4 data register 0f h (r/w) pdr5 port 5 data register 10 h (r/w) buzr buzzer register 11 h to 13 h vacancy 14 h (r/w) rcr1 remote control transmission register 1 15 h (r/w) rcr2 remote control transmission register 2 16 h to 17 h vacancy 18 h (r/w) t2cr timer 2 control register 19 h (r/w) t1cr timer 1 control register 1a h (r/w) t2dr timer 2 data register 1b h (r/w) t1dr timer 1 data register 1c h (r/w) smr serial mode register 1d h (r/w) sdr serial data register 1e h to 2f h vacancy
mb89180l series 26 (continued) note : do not use vacancies. address read/write register name register description 30 h (r/w) eie1 external interrupt 1 enable register 1 31 h (r/w) eif1 external interrupt 1 flag register 1 32 h (r/w) eie2 external interrupt 2 enable register 2 33 h (r/w) eif2 external interrupt 2 flag register 2 34 h to 5f h vacancy 60 h to 6f h (r/w) vram display data ram 70 h to 71 h vacancy 72 h (r/w) lcr1 lcd controller/driver control register 1 73 h to 7b h vacancy 7c h (w) ilr1 interrupt level setting register 1 7d h (w) ilr2 interrupt level setting register 2 7e h (w) ilr3 interrupt level setting register 3 7f h access prohibited itr interrupt test register
mb89180l series 27 n electrical characteristics 1. absolute maximum ratings (v ss = 0.0 v) (continued) parameter symbol rating unit remarks min max power supply voltage v cc v ss C 0.3 v ss + 4.0 v for mb89183l/185l v ss C 0.3 v ss + 7.0 v for mb89pv180/p185 lcd power supply voltage v1 to v3 v ss C 0.3 v ss + 4.0 v for mb89183l/185l v1 to v3 must not exceed v cc . v ss C 0.3 v ss + 7.0 v for mb89pv180/p185 v1 to v3 must not exceed v cc . input voltage v i1 v ss C 0.3 v cc + 0.3 v v i1 must not exceed v ss + 4.0 v for mb89183l/185l and v ss + 7.0 v for mb89pv180/p185. all pins except p20 to p27 without a pull-up resistor v i2 v ss C 0.3 v ss + 4.0 v p20 to p27 without a pull-up resistor for mb89183l/185l v ss C 0.3 v ss + 7.0 v p20 to p27 without a pull-up resistor for mb89pv180/p185 output voltage v o1 v ss C 0.3 v cc + 0.3 v v o1 must not exceed v ss + 4.0 v for mb89183l/185l and v ss + 7.0 v for mb89pv180/p185. all pins except p20 to p27, p40 to p47, and p50 to p57 without a pull-up resistor v o2 v ss C 0.3 v ss + 4.0 v p20 to p27, p40 to p47, and p50 to p57 without a pull-up resistor for mb89183l/185l v ss C 0.3 v ss + 7.0 v p20 to p27, p40 to p47, and p50 to p57 without a pull-up resistor for mb89pv180/p185 l level maximum output current i ol1 ? 10 ma all pins except p21, p26, and p27 i ol2 ? 20 ma p21, p26, and p27 l level average output current i olav1 ? 4ma all pins except p21, p26, p27, and power supply pins average value (operating current operating rate) i olav2 ? 8ma p21, p26, and p27 average value (operating current operating rate) l level total maximum output current s i ol ? 80 ma peak value l level total average output current s i olav ? 40 ma average value (operating current operating rate)
mb89180l series 28 (continued) warning: semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. do not exceed these ratings. 2. recommended operating conditions (v ss = 0.0 v) * : the liquid-crystal power supply range and optimum value vary depending on the characteristics of the liquid- crystal display element used. parameter symbol value unit remarks min max h level maximum output current i oh1 ? C5 ma all pins except p30 and power supply pins i oh2 ? C10 ma p30 h level average output current i ohav1 C2ma all pins except p30 and power supply pins average value (operating current operating rate) i ohav2 C4ma p30 average value (operating current operating rate) h level total maximum output current s i oh C20mapeak value h level total average output current s i ohav C10ma average value (operating current operating rate) power consumption p d 300mw operating temperature t a C40 +85 c storage temperature tstg C55 +150 c parameter symbol value unit remarks min max power supply voltage v cc 2.2 3.6 v normal operation assurance range for mb89183l/185l 2.7 6.0 v normal operation assurance range for mb89pv180 and mb89p185 1.5 3.6 v retains the ram state in stop mode for mb89183l/185l 1.5 6.0 v retains the ram state in stop mode for mb89pv180 and mb89p185 lcd power supply voltage v1 to v3 v ss v cc *v v1 to v3 pins lcd power supply range (the optimum value dependent on the lcd element in use.) operating temperature t a C40 +85 c
mb89180l series 29 operating voltage vs. main clock operating frequency (mb89pv180/p185) 1.0 3.0 4.0 2.0 1.0 2.0 3.0 operating voltage (v) 4.0 2.0 1.33 main clock operating freq. (mhz) min execution time (inst. cycle) ( m s) 4.0 5.0 2.2 2.7 4.2 1.0 6.0 3.5
mb89180l series 30 operating voltage vs. main clock operating frequency (mb89183l/185l) operating voltage vs. main clock operating frequency (mb89pv180/p185) and (mb89183l/185l) indicate the operating frequency of the external oscillator at an instruction cycle of 4/f ch . warning: the recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. all of the devices electrical characteristics are warranted when the device is operated within these ranges. always use semiconductor devices within their recommended operating condition ranges. operation outside these ranges may adversely affect reliability and could result in device failure. no warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. users considering application outside the listed conditions are advised to contact their fujitsu representatives beforehand. 1.0 3.0 4.0 2.0 1.0 2.0 3.0 operating voltage (v) 4.0 2.0 1.33 main clock operating freq. (mhz) min execution time (inst. cycle) ( m s) 4.0 4.5 2.2 4.2 1.0 3.6
mb89180l series 31 3. dc characteristics (1) pin dc characteristics (v cc = +3.0 v for mb89183l/185l; +5.0 v for mb89pv180/p185, v ss = 0.0 v, t a = C40 c to +85 c) (continued) parameter sym- bol pin condition value unit remarks min typ max h level input voltage v ih p00 to p07, p10 to p17, p20 to p27 ? 0.7 v cc ? v cc + 0.3 v cmos input v ihs rst , moda, ec, si, sck, int10 to int13, int20 to int27 0.8 v cc ? v cc + 0.3 v hysteresis input l level input voltage v il p00 to p07, p10 to p17, p20 to p27 v ss - 0.3 ? 0.3 v cc v cmos input v ils rst , moda, ec, si, sck, int10 to int13, int20 to int27 v ss - 0.3 ? 0.2 v cc v hysteresis input open-drain output pin application voltage v d1 p20 to p27, p31, p32, p40 to p47, p50 to p57 v ss - 0.3 ? v ss + 4.0 v for mb89183l/ 185l, p20 to p27, p40 to p47, and p50 to p57 without pull-up resistor only v ss - 0.3 ? v ss + 6.0 ? for mb89pv180/ p185, p20 to p27, p40 to p47, and p50 to p57 without pull-up resistor only h level output voltage v oh1 p00 to p07, p10 to p17 i oh = C2.0 ma 2.2 ?? v mb89183l/185l i oh = C2.0 ma 2.4 ?? v mb89pv180/p185 v oh2 p30 i oh = C8.0 ma 2.2 ?? v mb89183l/185l i oh = C6.0 ma 4.0 ?? v mb89pv180/p185 l level output voltage v ol p00 to p07, p10 to p17, p20,p22 to p25, p30 to p32, p40 to p47, p50 to p57 i ol = 1.8 ma ?? 0.4 v v ol2 p21, p26, p27 i ol = 8.0 ma ?? 0.4 v v ol3 rst i ol = 4.0 ma ?? 0.4 v mb89183l/185l i ol = 4.0 ma ?? 0.6 v mb89pv180/p185
mb89180l series 32 (continued) note : for pins which serve as the segment (seg8 to seg31) and ports (p40 to p47, p50 to p57 and p10 to p17), see the port parameter when these pins are used as ports and the segment parameter when they are used as segments. parameter sym- bol pin condition value unit remarks min typ max input leakage current (high-z output leakage current) i li1 p00 to p07, p10 to p17, p30, moda 0.45 v < v i < v cc ?? 5 m a without pull-up resistor i li2 p20 to p27, p31, p32, p40 to p47, p50 to p57 0.45 v < v i < 4.0 v 5 m a without pull-up resistor for mb89183l/ 185l 0.45 v < v i < 6.0 v 5 m a without pull-up resistor for mb89pv180/ p185 pull-up resistance r pull p00 to p07, p10 to p17, p20 to p27, p40 to p47, p50 to p57, rst v i = 0.0 v 25 50 100 k w with pull-up resistor common output impedance r vcom com0 to com3 v1 to v3 = +3.0 v 2.5 k w mb89183l/ 185l v1 to v3 = +5.0 v 2.5 k w mb89pv180/ p185 segment output impedance r vseg seg0 to seg31 v1 to v3 = +3.0 v 15 k w mb89183l/ 185l v1 to v3 = +5.0 v 15 k w mb89pv180/ p185 lcd divided resistance r lcd between v cc and v ss 300 500 750 k w lcd controller/ driver leakage current i lcdl v1 to v3, com0 to com3, seg0 to seg31 1 m a input capacitance c in other than v cc , v ss f = 1 mhz 10 pf
mb89180l series 33 (2) power supply current characteristics (v ss = 0.0 v, t a = C40 c to +85 c) * : the power supply current is measured at the external clock, open output pins, and the external lcd dividing resistor (or external input for the reference voltage). in the case of the mb89pv180, the current consumed by the connected eprom and ice is not included. parameter sym- bol pin condition value unit remarks min typ max power supply current* i cc1 v cc f ch = 4.2 mhz, v cc = 3.0 v, t inst = 4/f ch , main clock operation mode 1.32.5ma mb89183l, MB89185L f ch = 4.2 mhz, v cc = 5.0 v, t inst = 4/f ch , main clock operation mode 3.0 4.5 ma mb89pv180 3.8 6.0 ma mb89p185 i cc2 f ch = 4.2 mhz, v cc = 3.0 v, t inst = 64/f ch , main clock operation mode 0.180.7ma mb89183l, MB89185L 0.25 0.4 ma mb89pv180 0.85 1.4 ma mb89p185 i ccs1 f ch = 4.2 mhz, v cc = 3.0 v, t inst = 4/f ch , main clock sleep mode 0.32 1 ma mb89183l, MB89185L f ch = 4.2 mhz, v cc = 5.0 v, t inst = 4/f ch , main clock sleep mode 0.81.2ma mb89pv180, mb89p185 i ccs2 f ch = 4.2 mhz, v cc = 3.0 v, t inst = 64/f ch , main clock sleep mode 0.10.3ma mb89183l, MB89185L 0.20.3ma mb89pv180, mb89p185 i ccl f cl = 32.768 khz, t inst = 2/f cl , t a = +25 c, v cc = 3.0 v, subclock operation mode 0.050.1ma mb89183l, MB89185L, mb89pv180 0.65 1.1 ma mb89p185 i ccsl f cl = 32.768 khz, t inst = 2/f cl , t a = +25 c, v cc = 3.0 v, subclock sleep mode 1020 m a mb89183l, MB89185L 2550 m a mb89pv180, mb89p185 i cct f cl = 32.768 khz, t a = +25 c, v cc = 3.0 v, watch mode 515 m a mb89183l, MB89185L 1015 m a mb89p185, mb89pv180 i cch t a = +25 c, v cc = 3.0 v, stop mode 110 m a mb89183l, MB89185L t a = +25 c, v cc = 5.0 v, stop mode 0.110 m a mb89pv180, mb89p185
mb89180l series 34 4. ac characteristics (1) reset timing (mb89183l/185l : v cc = +3.0 v 10 %, v ss = 0.0 v, t a = C40 c to +85 c) (mb89pv180/p185 : v cc = +5.0 v 10 %, v ss = 0.0 v, t a = C40 c to +85 c) notes : t hcyl is the main clock oscillator period. if the reset pulse applied to the external reset pin (rst ) does not meet the specifications, it may cause malfunctions. use caution so that the reset pulse less than the specifications will not be fed to the external reset pin (rst ) . (2) power-on reset (v ss = 0.0 v, t a = C40 c to +85 c) note : make sure that power supply rises within the selected oscillation stabilization time. if power supply voltage needs to be varied in the course of operation, a smooth voltage rise is recommended. parameter symbol condition value unit remarks min max rst l pulse width t zlzh 48 t xcyl ns parameter symbol condition value unit remarks min max power supply rising time t r 50ms power-on reset function only power supply cut-off time t off 1ms due to repeated operations 0.2 v cc 0.2 v cc rst t zlzh 0.2 v 0.2 v 2.0 v 0.2 v t r v cc t off
mb89180l series 35 (3) clock timing (v ss = 0.0 v, t a = C40 c to +85 c) parameter symbol pin value unit remarks min typ max clock frequency f ch x0, x1 1 4.2 mhz main clock f cl x0a, x1a 32.768 khz subclock clock cycle time t hcyl x0, x1 238 1000 ns main clock t lcyl x0a, x1a 30.5 m s subclock input clock pulse width p wh p wl x0 20 ns external clock p whl p wll x0a 15.2 m s input clock rising/falling time t cr t cf x0 10 ns 0.8 v cc x0 x1 c 0 c 1 f ch open when a crystal or ceramic resonator is used when an external clock is used t hcyl 0.2 v cc p wh p wl t cf t cr x0 x0 x1 f ch main clock timing and conditions main clock conditions
mb89180l series 36 (4) instruction cycle parameter symbol value (typical) unit remarks instruction cycle (minimum execution time) t inst 4/f ch , 8/f ch , 16/f ch , 64/f ch m s(4/f ch ) t inst = 1.0 m s at f ch = 4 mhz 2/f cl m st inst = 61.036 m s at f cl = 32.768 khz x0a x1a c 0 c 1 rd open when a crystal or ceramic oscillator is used when the single-clock option is used x0a x1a f cl 0.8 v cc t lcyl 0.2 v cc p whl p wll t cf t cr x0a open when an external clock is used f cl x0a x1a subclock timing and conditions subclock conditions
mb89180l series 37 (5) serial i/o timing (mb89183l/185l : v cc = +3.0 v 10 %, v ss = 0.0 v, t a = C40 c to +85 c) (mb89pv180/p185 : v cc = +5.0 v 10 %, v ss = 0.0 v, t a = C40 c to +85 c) * : for information on t inst , see (4) instruction cycle. parameter symbol pin condition value unit remarks min max serial clock cycle time t scyc sck internal clock operation 2 t inst * m s sck ? so time t slov sck, so C200 + 200 ns valid si ? sck - t ivsh si, sck 1/2 t inst * m s sck - ? valid si hold time t shix sck, si 1/2 t inst * m s serial clock h pulse width t shsl sck external clock operation 1 t inst * m s serial clock l pulse width t slsh 1 t inst * m s sck ? so time t slov sck, so 0 200 ns valid si ? sck - t ivsh si, sck 1/2 t inst * m s sck - ? valid si hold time t shix sck, si 1/2 t inst * m s 0.2 v cc 0.8 v cc t slsh 2.4 v 0.2 v cc 0.8 v cc 0.8 v 0.8 v cc 0.2 v cc 0.8 v cc sck so si 0.2 v cc t shsl t shix t ivsh t slov external clock operation 0.8 v 2.4 v t scyc 2.4 v 0.2 v cc t shix 0.8 v 0.8 v t ivsh 0.8 v cc 0.2 v cc 0.8 v cc sck so si t slov internal clock operation
mb89180l series 38 (6) peripheral input timing (mb89183l/185l : v cc = +3.0 v 10 %, v ss = 0.0 v, t a = C40 c to +85 c) (mb89pv180/p185 : v cc = +5.0 v 10 %, v ss = 0.0 v, t a = C40 c to +85 c) * : for information on t inst, see (4) instruction cycle. parameter symbol pin value unit remarks min max peripheral input h pulse width 1 t ilih1 int10 to int13, ec 1 t inst * m s peripheral input l pulse width 1 t ihil1 1 t inst * m s peripheral input h pulse width 2 t ilih2 int20 to int27 2 t inst * m s peripheral input l pulse width 2 t ihil2 2 t inst * m s 0.2 v cc 0.8 v cc t ihil1 0.8 v cc int10 to int13, ec 0.2 v cc t ilih1 0.2 v cc 0.8 v cc t ihil2 0.8 v cc int20 to int27 0.2 v cc t ilih2
mb89180l series 39 n example characteristics (1) l level output voltage (2) h level output voltage 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 0 5 10 15 20 25 v ol2 vs. i ol v ol2 (v) i ol (ma) v cc = 3.5 v v cc = 4.0 v v cc = 2.0 v v cc = 2.5 v v cc = 3.0 v 0 0.2 0.4 0.6 0.8 1 1.2 0 5 10 15 20 25 v ol1 vs. i ol v ol1 (v) i ol (ma) v cc = 2.0 v v cc = 2.5 v v cc = 3.0 v v cc = 3.5 v v cc = 4.0 v 0 0.2 0.4 0.6 0.8 1 -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 0 v cc - v oh1 (v) i oh (ma) v cc = 3.5 v v cc = 4.0 v v cc = 2.0 v v cc = 2.5 v v cc = 3.0 v v cc - v oh1 vs. i oh 0 0.1 0.2 0.3 0.4 0.5 -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 0 v cc - v oh2 (v) i oh (ma) v cc = 3.5 v v cc = 4.0 v v cc = 2.0 v v cc = 2.5 v v cc = 3.0 v v cc - v oh2 vs. i oh
mb89180l series 40 (3) h level input voltage/l level input voltage (4) power supply current (external clock) (continued) 1234567 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 v cc (v) 1234567 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 v ihs v ils v cc (v) t a = + 25 c t a = + 25 c cmos input cmos hysteresis input v in (v) v in (v) v ihs : threshold when input voltage in hysteresis characteristics is set to h level v ils : threshold when input voltage in hysteresis characteristics is set to l level 0 0.02 0.04 0.06 0.08 0.1 0.12 0.14 12345 v cc (v) i cc1 (ma) t a = +25 c f ch = 4.2 mhz f ch = 1 mhz f ch = 3 mhz i cc1 vs. v cc (mask rom products) 0 0.02 0.04 0.06 0.08 0.1 0.12 0.14 12345 v cc (v) i cc2 (ma) t a = +25 c f ch = 4.2 mhz f ch = 1 mhz f ch = 3 mhz i cc2 vs. v cc (mask rom products)
mb89180l series 41 (continued) 0 0.02 0.04 0.06 0.08 0.1 0.12 0.14 12345 t a = +25 c f ch = 4.2 mhz f ch = 1 mhz f ch = 3 mhz i ccs2 vs. v cc (mask rom products) i ccs2 (ma) v cc (v) 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 12345 t a = +25 c f ch = 4.2 mhz f ch = 1 mhz f ch = 3 mhz i ccs1 vs. v cc (mask rom products) i ccs1 (ma) v cc (v) 0 0.2 0.4 0.6 0.8 1 1.2 12345 v cc (v) i cct ( m a) i cct vs. v cc (mask rom products) f cl = 32.768 khz t a = +25 ? c
mb89180l series 42 (continued) (5) pull-up resistance 0 1 2 3 4 5 6 12345 v cc (v) i ccsl ( m a) i ccsl vs. v cc (mask rom products) f cl = 32.768 khz t a = +25 ? c 0 40 80 120 160 200 2 2.5 3.5 4.5 5.5 v cc (v) r pull (k ) r pull vs. v cc 345 t a = +125 ? c t a = +93 ? c t a = +25 ? c t a = +40 ? c
mb89180l series 43 n mask options (continued) no. part number mb89183l/185l mb89p185 mb89pv180 specifying procedure specify when ordering masking set with eprom programmer setting not possible 1 pull-up resistors (pxx) p00 to p07, p10 to p17 selectable per pin (the pull-up resistors for p10 to p17 are available only when these pins are not set as segment outputs.) can be set per pin (p10 to p17 are available only when segment output is not selected.) fixed to without pull-up resistor 2 pull-up resistors (pxx) p40 to p47, p50 to p57 selectable per pin (available only when these pins are not set as segment outputs.) fixed to without pull-up resistor fixed to without pull-up resistor 3 pull-up resistors (pxx) p20 to p27 selectable per pin fixed to without pull-up resistor fixed to without pull-up resistor 4 power-on reset (por) with power-on reset without power-on reset selectable selectable fixed to with power-on reset 5 selection of oscillation stabilization time (osc) the initial value of the oscillation stabilization time for the main clock can be set by selecting the values of the wtm1 and wtm0 bits on the right. selectable osc 0 : 2 2 /f ch 1 : 2 12 /f ch 2 : 2 16 /f ch 3 : 2 18 /f ch selectable wtm1 wtm0 0 0 : 2 2 /f ch 0 1 : 2 12 /f ch 1 0 : 2 16 /f ch 1 1 : 2 18 /f ch fixed to oscillation stabilization time of 2 16 / f ch 6 main clock oscillation type (xsl) crystal or ceramic resonator crystal or ceramic crystal or ceramic crystal or ceramic 7 reset pin output (rst) with reset output without reset output selectable selectable fixed to with reset output 8 clock mode selection (clk) dual-clock mode single-clock mode selectable selectable fixed to dual-clock mode
mb89180l series 44 (continued) no. part number mb89183l/185l mb89p185 mb89pv180 specifying procedure specify when ordering masking select by version number select by version number 9 lcd output pin configuration choices specify by the option combinations listed below ?? seg = 6: p40 to p47 segment output p50 to p57 segment output p10 to p17 segment output specify as seg = 6 C101 : seg 32 pins C101 : seg 32 pins seg = 5: p40 to p47 segment output p50 to p57 segment output p10 to p13 segment output p14 to p17 port output specify as seg = 5 C102 : seg 28 pins C102 : seg 28 pins seg = 4: p40 to p47 segment output p50 to p57 segment output p10 to p17 port output specify as seg = 4 C103 : seg 24 pins C103 : seg 24 pins seg = 3: p40 to p47 segment output p50 to p53 segment output p54 to p57 port output p10 to p17 port output specify as seg = 3 C104 : seg 20 pins C104 : seg 20 pins seg = 2: p40 to p47 segment output p50 to p57 port output p10 to p17 port output specify as seg = 2 C105 : seg 16 pins C105 : seg 16 pins seg = 1: p40 to p43 segment output p44 to p47 port output p50 to p57 port output p10 to p17 port output specify as seg = 1 C106 : seg 12 pins C106 : seg 12 pins seg = 0: p40 to p47 port output p50 to p57 port output p10 to p17 port output specify as seg = 0 C107 : seg 8 pins C107 : seg 8 pins
mb89180l series 45 n ordering information part number package remarks mb89183lpf MB89185Lpf mb89p185pf-101 mb89p185pf-102 mb89p185pf-103 mb89p185pf-104 mb89p185pf-105 mb89p185pf-106 mb89p185pf-107 64-pin plastic qfp (fpt-64p-m06) mb89183lpfm MB89185Lpfm mb89p185pfm-101 mb89p185pfm-102 mb89p185pfm-103 mb89p185pfm-104 mb89p185pfm-105 mb89p185pfm-106 mb89p185pfm-107 64-pin plastic qfp (fpt-64p-m09) mb89183lpfv MB89185Lpfv 64-pin plastic sqfp (fpt-64p-m03) mb89pv180cf-101 mb89pv180cf-102 mb89pv180cf-103 mb89pv180cf-104 mb89pv180cf-105 mb89pv180cf-106 mb89pv180cf-107 64-pin ceramic mqfp (mqp-64c-p01)
mb89180l series 46 n n n n package dimensions (continued) 64-pin plastic sqfp (fpt-64p-m03) note 1) * : these dimensions do not include resin protrusion. note 2) pins width and pins thickness include plating thickness. note 3) pins width do not include tie bar cutting remainder. 64-pin plastic qfp (fpt-64p-m06) note 1) * : these dimensions do not include resin protrusion. note 2) pins width and pins thickness include plating thickness. note 3) pins width do not include tie bar cutting remainder. lead no. details of "a" part 0.25(.010) (stand off) (.004.004) 0.100.10 (.024.006) 0.600.15 (.020.008) 0.500.20 1.50 +0.20 C0.10 +.008 C.004 .059 0 ? ~8 ? "a" 0.08(.003) (.006.002) 0.1450.055 0.08(.003) m (.008.002) 0.200.05 0.50(.020) 12.000.20(.472.008)sq 10.000.10(.394.004)sq index 49 64 33 48 17 32 16 1 2003 fujitsu limited f64009s-c-5-8 c (mounting height) * dimensions in mm (inches) c 2003 fujitsu limited f64013s-c-5-5 0.20(.008) m 18.700.40 (.736.016) 14.000.20 (.551.008) 1.00(.039) index 0.10(.004) 119 20 32 52 64 33 51 20.000.20(.787.008) 24.700.40(.972.016) 0.420.08 (.017.003) 0.170.06 (.007.002) 0~8 ? 1.200.20 (.047.008) 3.00 +0.35 C0.20 (mounting height) .118 +.014 C.008 0.25 +0.15 C0.20 .010 +.006 C.008 (stand off) details of "a" part "a" 0.10(.004) * * dimensions in mm (inches)
mb89180l series 47 (continued) 64-pin plastic qfp (fpt-64p-m09) note 1) * : these dimensions do not include resin protrusion. note 2) pins width and pins thickness include plating thickness. note 3) pins width do not include tie bar cutting remainder. 64-pin ceramic mqfp (mqp-64c-p01) c 2003 fujitsu limited f64018s-c-3-5 0.65(.026) 0.10(.004) 116 17 32 49 64 33 48 12.000.10(.472.004)sq 14.000.20(.551.008)sq index 0.320.05 (.013.002) m 0.13(.005) 0.1450.055 (.0057.0022) "a" .059 C.004 +.008 C0.10 +0.20 1.50 0~8 ? 0.25(.010) (mounting height) 0.500.20 (.020.008) 0.600.15 (.024.006) 0.100.10 (.004.004) details of "a" part (stand off) 0.10(.004) * dimensions in mm (inches) c 1994 fujitsu limited m64004sc-1-3 15.58?.20 (.613?008) 16.30?.33 (.642?013) 18.70(.736)typ index area 0.30(.012) typ 1.27?.13 (.050?005) 22.30?.33 (.878?013) 24.70(.972) typ 10.16(.400) typ 12.02(.473) typ 14.22(.560) typ 18.12?.20 (.713?008) 1.27?.13 (.050?005) 0.30(.012)typ 7.62(.300)typ 9.48(.373)typ 11.68(.460)typ 0.50(.020)typ 0.15?.05 (.006?002) 10.82(.426) max 0.40?.10 (.016?004) .047 ?008 +.016 ?.20 +0.40 1.20 0.40?.10 (.016?004) 1.00?.25 (.039?010) 18.00(.709) typ 1.00?.25 (.039?010) 12.00(.472)typ .047 ?008 +.016 ?.20 +0.40 1.20 dimensions in mm (inches)
mb 89180l series fujitsu limited all rights reserved. the contents of this document are subject to change without notice. customers are advised to consult with fujitsu sales representatives before ordering. the information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of fujitsu semiconductor device; fujitsu does not warrant proper operation of the device with respect to use based on such information. when you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. fujitsu assumes no liability for any damages whatsoever arising out of the use of the information. any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of fujitsu or any third party or does fujitsu warrant non-infringement of any third-partys intellectual property right or other right by using such information. fujitsu assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. the products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). please note that fujitsu will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. any semiconductor devices have an inherent chance of failure. you must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. if any products described in this document represent goods or technologies subject to certain restrictions on export under the foreign exchange and foreign trade law of japan, the prior authorization by japanese government will be required for export of those products from japan. f0302 ? fujitsu limited printed in japan

▲Up To Search▲

Price & Availability of MB89185L

	To Download MB89185L Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .